Current sensors | Liquid Level Sensors | Flow and Pressure Sensors
Moisture / Humidity Sensors | Temperature Sensors | CO2 and PH Sensors
Output Control | Power Supply and Battery powered

Energy parameter monitoring.
AC Current Sensor. AC Current Switch. Ground Fault Sensor,
DC Current Switch and DC Current Transducer.
DC Hall Effect Current Transducers and
True RMS AC Current Transducer

AC current sensor connection

AC current switch can be used to monitor fan and pump status, motors, compressors, and any other electrical equipment for proper operation. A change in the operating current may indicate mechanical failure or that the unit has been turned off. AC current sensors can be used in load trending (current monitoring) type applications.

AC Current sensors (split or solid core). The CTA and CTV Series current sensors monitor the current flowing to electrical equipment or buildings. The magnitude of this current is then converted into a linear 4...20 mA or 0...10Vdc output signal. All of these sensors have jumper selectable input ranges 0-10, 0-20, 0-50A for CTV-50 or SCTV-50 (or 0-100, 0-200, 0-250A for CTV-250 or SCTV-250). These current sensors should be used in load trending (current monitoring) type applications. The current sensors are fast acting, reliable, and extremely easy to install. No additional din rail mounting clips are necessary, due to the unique design of the integral din rail mounting flange.
The CS series current sensors monitor the current flowing to electrical equipment or buildings. The magnitude of this current is then converted into a linear 4-20mA or 0 to 10 VDC output signal, which can be monitored by a Building Management System. The units have jumper selectable input ranges. These current sensors should be used in load trending (current monitoring) type applications. CS-SD10L or CS-SP10L - range 0...10/20/50A or for CS-SD10 or CS-SP10 0...100/150/200A.

AC current switch connection

AC current switch can be used to monitor fan and pump status, motors, compressors, and any other electrical equipment for proper operation. A change in the operating current may indicate mechanical failure or that the unit has been turned off.

AC Current switch (split or solid core). AC current switches should be used in applications in which a “Go/No Go” current switch is required. A current switch can be used to monitor fan and pump status, motors, compressors, and any other electrical equipment for proper operation. A change in the operating current may indicate mechanical failure or that the unit has been turned off.
The CSW series of AC current switches activate a normally open (NO) contact closure via a solid-state switch whenever the monitored primary circuit current exceeds a pre-set level. Models are available to switch various load types. The CSW series current switches can be used to monitor devices with a maximum continuous operating current of up to 200 Amps and the power supply is induced from the conductor being monitored. Fixed or adjustable setpoint
The CS-F series current switches are available in a solid-core or split-core with Normally-Open (N/O) output configurations. All of these sensors will have a solid-state output with a fixed trip point (setpoint). These current switches are ideal for providing status information on any type of AC current using equipment.

Ground Fault Sensor, DC Current Switch and
DC Current Transducer connection

Ground Fault sensor - Normally Energized: protection from fault or loss of control power. Normally Deenergyzed: protection from faults only when control power is applied. Current Operated Switches. Input. With Relay output (SPDT) or Solid State Output (Normally Open). DC Current Transducer for DC measurement.

AKS-C NOAC Ground Fault Sensor, Factory adjusted set point. NO output. Primary current 5 - 950 mA AC. Normally Energized: protection from fault or loss of control power. Normally Deenergyzed: protection from faults only when control power is applied. DKS 100 C Current Operated Switches. Input - 4-20A, 10-50A, 15-100A (with manual jumper). Hysteresis is 5% of set point. DFS 100C SDT - Relay output (SPDT) or DKS 100C NOW - Solid State Output (Normally Oupen). DC Current Transducer. Split or solid core. 0-5VDC output DK-B5 0-10VDC output DK-B10 proportional to measured current. For DC measurement. Jumper selectable range.

DC Hall Effect Current Transducers
True RMS AC Current Transducer

The CR5200 Series, DC Hall Effect Current Transducers are designed to output a DC signal which is proportional to a DC current input signal. These devices are designed for direct current only, targeting them towards general and daily applications. 0-5Vdc or 4-20mA DC outputs. Supply Voltage: 24 VDC. The CR4100 Series True RMS Current Transducers and Transmitters are designed for applications where AC current waveforms are not purely sinusoidal. More precise and accurate than other transducers, these devices are ideal in chopped wave and phase fired control systems. 0-5Vdc or 4-20mA DC outputs.



Current sencor compatibel with BR16GM-2A/-4A, BR160GM-2A/-4A, BR160SM-2A/-4A,
BR128GM-4A/-Pt1000, BR1280GM Current switch compatibel with all our modules BR16GM, BR160GM, BR160SM, BR128GM, BR1280GM