|
|  | | Cable Tester |      |
| |
PC based Cable Tester BieneCableTester01 |
| BieneCableTester01
- is a high performance, low cost, portable PC based Cable Tester
for diagnostic wide range of products, including cables, wiring harnesses, distribution
panels, wiring looms and switch assemblies. Maximum numbers of connectors pin
- 104. Cable Tester display visually pinpoints problems when wiring errors are
detected, and offers one-second pass/fail functional testing for cable production
environments. Test type: static, continuous static, dynamic (model BieneCableTester01D).
An on-line base holds an unlimited number of User cables. Choose from
a wide variety of plug-in adapter to mate with most standard cables. The system
can automatically learn a cable from a known good sample. Tests PC cables, CISCO
cables, Centronics and RS-232 cables, cables with connectors type DB Sub 9, 15,
25, 50, High-Density D-Submini 15, 26, 44, 62, Centronics 36, 50, SCSI cables
- Centronics and miniCentronics 50 (SCSI-I), Ultra SCSI cables (MC68,80,100),
miniD 50 (SCSI-II), miniD 68 (SCSI-III), V35, Telco cables (Centronics 50), IDC
and High-Density IDC Flat cables, Router and Network Cables, Smart Serial
Connectors Cables. Tests cables for opens, short, pin-to-pin configurations
and misswired connections.
 |
BieneCableTester
- is portable PC based Cable Tester that connects to the parallel port of your
desktop or laptop computer. For testing any types cables you will need an adapters.
This adapters plug into two 60 pin connectors.
Features: - connects
to the parallel port (EPP mode)
- maximum 104x104 pin cable testing
- static
single or continuous test for shorts, opens and misswired connections
- dynamic
test (model BieneCableTester01D)
- faults
identified for opens, short, pin-to-pin configurations, misswired connections.
- create
connection table from sample-cable
- create cable wire list
- save
and print results
- report error to display or printer
- diagnostic
self test
- user defined pin names
- the software runs on Windows
98.
- one-year warranty with free technical support; You will also receive
free software upgrades.
Static test: this applies a voltage to each pin in turn and checks
the response of all other pins (on the left and right connectors of cables). Test
runs one cycle for all pins. This is checked against the required response. This
test will detect missing connections (“Opens”), Extra Connections (“Shorts”) and
misswired connections (“wrong pins"). The test voltage is usually 3.3 Volts
D.C.
Continuous static test: this applies a voltage to each
pin in turn and checks the response of all other pins (on the left and right connectors
of cables). Test runs N cycles. This is checked against the required response.
This test will detect missing connections (“Opens”), Extra Connections (“Shorts”)
and misswired connections (“wrong pins"). The test voltage is usually 3.3
Volts D.C.
Dynamic test (model BieneCableTester01D):
this applies a 4 impuls to each pin in turn and checks the response of all other
pins (on the left and right connectors of cables). This is checked against the
required response. This test will detect dynamic error.
Adaptors
type - DB9,15,25,50 male and female
- DB15,26,44 HD
male and female
- v.35 male and female
- Centronics Connectors CN36
male and female
- SCSI Connectors MD26, 50, 68 male
- SCSI Connectors
MC80, 100 male
- Telco CN50 male and female
- IDC Flat-Cable Connectors
- RJ11, RJ45 Connectors
- Universal adapter - kit of universal printed
board, connectors, spacers, screws. Use this set to mount your adapters.
  
Tehnical Specifications General
Specifications
| Cable type: | any cables with
connectors from 2 to 104 pin: SCSI Cable, CISCO Cable, CENTRONICS Cable, RS-232
Cable... | | Maximum numbers of pin: | 104
or 103+ chassis pin | | Frequence (dynamic
test): | from 10MHz to
10 kHz (BieneCableTester01d) | | Pin in the
net: | < 40 | Software
| Software Compatibility: | Windows 98 |
| Interface: | Parallel port
LPT1 or LPT2 | | Mode: | EPP |
| Display resolution: | 1024 x 768 |
Hardware
| Include: | cable tester,
software, user manual, power supply. Adapters - after request. |
| Power Supply: | external |
| Phisical Dimension | 260 x 130 x 54 mm |
| Adapter Dimension: | 104 x 118 mm |
|
| |
